Home

Integration Systems

Relay Controller provides a simple way to connect up to 12 output groups of 2-wire relays to a LonWorks Network The only connections required are to the relay outputs and to the 2-wire data signal

24-Relay DMX Interface

  • The DMX-1005 Interface provides a means to control Douglas lighting control low voltage relays using Entertainment Industry Standard DMX512 protocol
  • The relays are switched in response to the DMX512 signal
  • Relay outputs are patched, or programmed, to the DMX channels using the push button controls and display on the DMX-1005. Soft patching is supported
  • The DMX-1005 Interface has 24 outputs that switch Douglas relays. Standard Douglas relay switches and relay scanners can be used in conjunction with the DMX-1005
  • The DMX-1005 Interface supports ANSI E1.20 Remote Device Management over the DMX512 signal line, which allows status monitoring

WNG-2133 BACnet Lighting Gateway

  • The WNG-2133 BACnet Gateway allows a stand-alone Douglas W-2000 or MC-6000 lighting control system to operate independently, but gives an external BACnet network access to switch and monitor all relay groups, obtain relay group status, switch any individual relays and obtain individual relay status within the Douglas system
  • The WNG-2133 Lighting Gateway streamlines the inclusion and integration of a Douglas lighting control network into a larger BACnet IP network
  • With the WNG-2133 Lighting Gateway, network management, node configuration and group programming can still be performed by the Douglas W-2000 lighting control system or the Douglas MC-6000 lighting control system interface

WBI-2651 BACnet Node

  • The WBI-2651 BACnet Node plugs into a Programmable Relay Scanner and incorporates that scanner into a BACnet network
  • The WBI-2651 allows programming, monitoring and control of 5 output groups, and control and monitoring of 24 individual relays and 5 switch inputs
  • The WBI-2651 BACnet Node can be integrated with any other system that uses BACnet

ALC3-2800-750 Lonworks Active Link Power Interface

  • The ALC3-2800-750 Link Power Supply provides conditioned power for a LonWorks link power network
  • The ALC3-2800-750 can be powered by either 24VAC or 24VDC
  • Isolates power supply from the communication signal and provides proper termination impedance for the balanced data signals
  • 'Centers' the output voltage (data signal) with respect to ground, resulting in "Net+" as +21V and and "Net-" as -21V
  • Protects outputs against:
    • shorts
    • ground faults
    • current overdraw
    • undervoltage

WNS-2313 Data Line Switch Module

  • The WNS-2313 Data Line Switch Module provides 3 switches, each with an ON/OFF LED indicator. Switch Modules can be ganged to provide larger switch stations
  • Each WNS-2313 Switch Module on a LonWorks lighting control network has an address which is set with the rotary, 16-position dial on the back (for self-configured networks) or by the WNP-2150 Network Manager or Building Management System (for externally-configured networks). If two modules have the same address, they will operate in parallel
  • Up to 16 WNS-2313 Switch Modules can exist within the same self-configured lighting control network
  • Each of the 3 switches on the module can be programmed to control output relays anywhere within the network
  • WNS-2313 Switch Modules install in standard wall boxes
  • The LED indicators on the modules have auxiliary flashing patterns for programming aids and fault diagnosis

WPS-5952 Indoor Photo Sensor, LonWorks Compatible

  • The WPS-5952 Indoor Photo Sensor is compatible with LonWorks networks
  • Ceiling-mounted photo sensor that measures ambient light levels reflected from surfaces below
  • Transmits measured light value in lux to the LonWorks network
  • Wink and service LEDs and service button are under the front snap-on cover
  • Connections (to data signal and to 24VAC power) are clearly labeled on the back of the unit

WPS-5942 Outdoor Photo Sensor, LonWorks Compatible

  • Compatible with LonWorks networks
  • Usable as a device within a LonWorks lighting control network regulated by a WNP-2150 Network Manager
  • Measures true ambient light levels, ranging from 0 to 65,535 lux
  • Ideal for situations requiring accurate light level switching such as skylit areas or outdoor signs
  • Weatherproof, rugged and resistant to harsh environments
  • An indoor ceiling-mount version available, the WPS-5952 Indoor Photo Sensor

WNS-2308 Eight-Input Node

  • The WNS-2308 Eight-Input Node can can provide switch inputs for up to 8 groups of relays that are controlled by programmable relay scanners within a LonWorks Network
  • Each node input can be configured to interface with a variety of hardware types and to operate in a variety of switching modes
  • Easy to configure, with instructions printed on front face
  • Up to 8 WNS-2308 Eight-input Nodes can be networked within a Douglas LonWorks self-configuring lighting control system using a simple 2-wire data signal
  • WNS-2308 Eight-input Nodes can be integrated into other control systems that use the LonWorks protocol

WNX-2624 Network Node

  • The WNX-2624 Network Node plugs into a WRS-2224 Programmable Relay Scanner and connects that scanner into a LonWorks Network
  • Network functions are performed within the Network Node
  • Up to 24 WNX-2624 Network Nodes and their corresponding scanners can be networked within a Douglas LonWorks self-configuring lighting control system using a simple 2-wire data signal. One of the Network Nodes is designated as 'Network Manager' (by a simple switch setting) and will automatically configure other devices as they are added to the system
  • The WNX-2624 can be integrated into any other control system that uses the LonWorks standard

WBC-2512 Ballast Controller

  • The WBC-2512 Ballast Controller is a LonWorks-compliant device which can control any dimming ballasts that utilize the 0-10V control method
  • 12 outputs available, each dimmable to its own unique level
  • Up to 50 ballasts can be connected to one output
  • Can control any ballasts that utilize the 0-10V control method
  • Can operate in conjunction with the WPS-5952 Indoor Photo Sensor and/or the WNR-2112 Relay Controller for controlling ballasts within a Lonworks system
Syndicate content